LT2013s Wide Flat Panel
Monitor User’s Guide
Contents
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
General Safety guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Chapter 1. Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Shipping contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Notice for use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Types of adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Monitor controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Cable lock slot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Setting up your monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Connecting and turning on your monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Registering your option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Chapter 2. Adjusting and using your monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Comfort and accessibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Arranging your work area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Positioning your monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Quick tips for healthy work habits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Accessibility information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Adjusting your monitor image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Using the direct access controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Using the On-Screen Display (OSD) controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Selecting a supported display mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Image rotation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Understanding power management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Caring for your monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10
Detaching the monitor base and stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Wall Mounting (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Chapter 3. Reference information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Monitor specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Manual image setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Manually installing the monitor driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Installing the monitor driver in Windows 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Installing the monitor driver in Windows 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Installing the monitor driver in Windows Vista . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Getting further help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Service information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Customer responsibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Service parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Appendix A. Service and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Registering your option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Online technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Telephone technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Appendix B. Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Recycling information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
Contents ii
Chapter 1. Getting started
This User’s Guide contains detailed information on the your Flat Panel Monitor. For a quick
overview, please see the Setup Poster that was shipped with your monitor.
Shipping contents
The product package should include the following items:
•
Setup Poster
•
•
•
•
Reference and Driver CD
Flat Panel Monitor
Power Cord
Analog Interface Cable
Notice for use
To set up your monitor, please see the illustrations below.
Note: Do not touch the monitor within the screen area. The screen area is glass and can be
damaged by rough handling or excessive pressure.
26°
1. Carefully lay the monitor on a flat surface.
2. Put the base to the monitor.
Note: To attach a VESA mount, please see "Wall Mounting (Optional)"on page
.
2-9
Chapter 1.
1-1
Product overview
This section will provide information on adjusting monitor positions, setting user controls, and
using the cable lock slot.
Types of adjustments
Tilt
Please see the illustration below for an example of the tilt range.
-5°
22°
Monitor controls
Your monitor has controls on the front which are used to adjust the display.
For information on how to use these controls, please see "Adjusting your monitor image"on
page 2-3.
Chapter 1.
1-2
Setting up your monitor
This section provides information on how to set up your monitor.
Connecting and turning on your monitor
Note: Be sure to read the Safety information located on page iii before carrying out this
procedure.
1. Power off your computer and all attached devices, and unplug the computer power cord.
2. Connect the cables according to below icon indication.
Chapter 1.
1-4
3.
Connect one end of the analog signal cable to the monitor D-SUB connector and the other
end to the computer.
Chapter 1.
1-5
4. Insert the power cord into the monitor, then plug the monitor power cord and the computer
cord into grounded electrical outlets.
Note: A certified power supply cord has to be used with this equipment. The relevant national
installation and or equipment regulations shall be considered. A certified power supply cord
not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation
H05VV-F 3G 0.75mm2 or H05VVH2-F2 3G0.75mm2) shall be used. Alternative a flexible
cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0.75mm2) shall
be used.
5.
Power on the monitor and the computer.
Chapter 1.
1-6
To install the monitor driver, insert the Reference and Driver CD, click Install driver, and
follow the on-screen instructions.
6.
To optimize your monitor image, press the Automatic Image Setup key.
Automatic image setup requires that the monitor is warmed up for at least 15 minutes.
This is not required for normal operation.
7.
Note: If automatic image setup does not establish the image that you prefer, perform manual
image setup. See "Manual image setup"on page 3-4.
Registering your option
Thank you for purchasing this Lenovoâ„¢ product. Please take a few moments to
register your Product and provide us with information that will help Lenovo to better
serve you in the future. Your feedback is valuable to us in developing product and
services that are important to you, as well as in developing better ways to
communicate with you. Register your option on the following Web site:
Lenovo will send you information and updates on your registered product unless you
indicate on the Web site questionnaire that you do not want to receive further
information.
Chapter 1.
1-7
Chapter 2. Adjusting and using your monitor
This section will give you information on adjusting and using your monitor.
Comfort and accessibility
Good ergonomic practice is important to get the most from your personal computer
and to avoid discomfort. Arrange your workplace and the equipment you use to suit
your individual needs and the kind of work that you perform. In addition, use
healthy work habits to maximize your performance and comfort while using your
computer. For more detailed information on any of these topics, visit the Healthy
Arranging your work area
Use a work surface of appropriate height and available working area to allow you to
work in comfort.
Organize your work area to match the way you use materials and equipment. Keep
your work area clean and clear for the materials that you typically use and place the
items that you use most frequently, such as the computer mouse or telephone, within
the easiest reach.
Equipment layout and setup play a large role in your working posture. The following
topics describe how to optimize equipment setup to achieve and maintain good
working posture.
Positioning your monitor
Position and adjust your computer monitor for comfortable viewing by considering
the following items:
•
Viewing distance: Optimal viewing distances for monitors range from
approximately 510mm to 760mm (20 in to 30 in) and can vary depending on
ambient light and time of day. You can achieve different viewing distances by
repositioning your monitor or by modifying your posture or chair position. Use a
viewing distance that is most comfortable for you.
•
Monitor height: Position the monitor so your head and neck are in a comfortable
and neutral (vertical, or upright) position. If your monitor does not have height
adjustments, you might have to place books or other sturdy objects under the
base of the monitor to achieve the desired height. A general guideline is to
position the monitor such that the top of the screen is at or slightly below your
eye-height when you are comfortably seated. However, be sure to optimize your
monitor height so the line of site between your eyes and the center the monitor
suits your preferences for visual distance and comfortable viewing when your eye
muscles are in a relaxed state.
•
•
Tilt: Adjust the tilt of your monitor to optimize the appearance of the screen
content and to accommodate your preferred head and neck posture.
General location: Position your monitor to avoid glare or reflections on the screen
from overhead lighting or nearby windows.
The following are some other tips for comfortable viewing of your monitor:
Use adequate lighting for the type of work you are performing.
•
Chapter 2.
2-1
•
•
Use the monitor brightness, contrast controls, if equipped to optimize the image
on your screen to meet your visual preferences.
Keep your monitor screen clean so you can focus on the screen’s contents.
Any concentrated and sustained visual activity can be tiring for your eyes. Be sure to
periodically look away from your monitor screen and focus on a far object to allow
your eye muscles to relax. If you have questions on eye fatigue or visual discomfort,
consult a vision care specialist for advice.
Quick tips for healthy work habits
The following information is a summary of some important factors to consider to help
you remain comfortable and productive while you use your computer.
•
Good posture starts with equipment setup: The layout of your work area and the
setup of your computer equipment have a large effect on your posture while
using your computer. Be sure to optimize the position and orientation of your
equipment by following the tips outlined in "Arranging your work area"on page
2-1 so you can maintain a comfortable and productive posture. Also, be sure to
use the adjustment capabilities of your computer components and office furniture
to best suit your preferences now and as your preferences change over time.
•
•
Minor changes in posture can help avoid discomfort: The longer you sit and
work with your computer, the more important it is to observe your working
posture. Avoid assuming any one posture for an extended period of time.
Periodically make minor modifications in your posture to help deter any
discomforts that might arise. Make use of any adjustments that your office
furniture or equipment provide to accommodate changes in posture.
Short, periodic breaks help ensure healthy computing: Because computing is
primarily a static activity, it is particularly important to take short breaks from
your work. Periodically, stand up from your work area, stretch, walk for a drink
of water, or otherwise take a short break from using your computer. A short break
from work gives your body a welcome change in posture and helps to ensure you
remain comfortable and productive while you do work.
Accessibility information
Lenovo is committed to providing greater access to information and technology to
people with disabilities. With assistive technologies, users can access information in
the way most appropriate to their disability. Some of these technologies are already
provided in your operating system; others can be purchased through vendors or
accessed at:
bidx?OpenForm
Chapter 2.
2-2
Adjusting your monitor image
This section describes the control features to adjust your monitor image.
Using the direct access controls
The direct access controls can be used when the On Screen Display (OSD) is not
displayed.
Table 2-1. Direct access controls
Icon
Control
DDC-CI
Exit
Description
Press and hold for 10 seconds to enable or disable
the DDC-CI function
Exit from menu
Image Setup
Activates automatic image adjustment
Brightness
Menu
Direct access to Brightness adjustment
Enter menu
Chapter 2.
2-3
Using the On-Screen Display (OSD) controls
To adjust the settings, the user controls can be viewed through the OSD.
To use the controls:
1. Press
to open the main OSD menu.
2. Use
or to move among the icons. Select an icon and press
to access that
or
to make adjustments. Press
function. If there is a sub-menu, you can move between options using
then press
to save.
,
to select that function. Use
or
3. Press
to move backwards through the sub-menus and exit from the OSD.
4. Press and hold
for 10 seconds to lock the OSD. This will prevent accidental
adjustments to the OSD. Press and hold
allow adjustments to the OSD.
for 10 seconds to unlock the OSD and
5. Enables DDC/CI by default. Use OSD Exit Key, Press and hold
for 10 seconds
to disable / enable DDC/CI function. The words "DDC/CI disable" shows on the
screen.
Chapter 2.
2-4
Table 2-2. OSD functions
OSD Icon on Main
Controls and
Adjustments
(Analog)
Menu
Submenu
Description
Adjusts overall screen
brightness
Brightness
Brightness/
Contrast
Adjusts difference between
light and dark areas
Contrast
Moves image left or right.
Moves image up or down.
Horizontal Position
Vertical Position
Image Position
Image Setup
Optimizes image (size, position, phase and clock).
Automatic
Manual
Manually optimizes image. See "Manual image
setup"on page 3-4.
•
•
•
Clock
Phase
Save
Adjusts intensity of red, green, and blue.
Preset mode
Color
Image Properties
•
•
•
•
Neutral
sRGB
Reddish
Bluish
Custom
•
•
•
•
Red: Increases or decreases the saturation of
’red’ in the image.
Green: Increases or decreases the saturation of
’green’ in the image.
Blue: Increases or decreases the saturation of
’blue’ in the image.
Save: Saves the custom color choices.
•
•
Selects type of scaled image.
Original AR:Same Aspect Ratio with input
signal.
Scaling
•
Full Screen: Expand image to full screen..
Chapter 2.
2-5
Table 2-2. OSD functions
OSD Icon on Main
Controls and
Adjustments
(Analog)
Menu
Submenu
Description
Shows resolution, refresh rate, and product details.
Note: This screen does not allow any changes to
the settings.
Information
Options
Changes languages of menu.
Note: The language chosen only affects the
language of the OSD. It has no effect on any
software running on the computer.
Menu Language
Menu Position
Adjusts menu location.
Default
Default returns the menu position to the default
settings.
Custom
•
Horizontal: Changes the horizontal position of
the OSD.
•
Vertical: Changes the vertical position of the
OSD.
Save
•
•
•
Save the custom position choices.
Cancel
Reset
Factory default
Accessibility
Reset monitor to the original settings.
Changes button repeat rate and menu time-out setting.
Button repeat rate:
Select or to change.
•
•
•
Off
Default
Slow
Menu time out: Sets the length of time the
OSD will remain active after the last time a button
is pressed.
Exit from menu.
Exit
Chapter 2.
2-6
Selecting a supported display mode
The display mode the monitor uses is controlled by the computer. Therefore, refer to
your computer documentation for details on how to change display modes.
The image size, position and shape might change when the display mode changes.
This is normal and the image can be readjusted using automatic image setup and the
image controls.
Unlike CRT monitors, which require a high refresh rate to minimize flicker, LCD or
Flat Panel technology is inherently flicker-free.
Note: If your system has previously been used with a CRT monitor and is currently
configured to a display mode outside the range of this monitor, you may need to
reattach the CRT monitor temporarily until you have re-configured the system;
preferably to 1600X900 at 60 Hz, which is the Native Resolution Display mode.
The display modes shown below have been optimized at the factory.
Table 2-3. Factory set display modes
Timing
640 x 350
640 x 480
700 x 570
720 x 400
800 x600
832 x 624
1024 x 768
1366 x 768
1152 x 864
Refresh rate(Hz)
70Hz
60Hz 72Hz 75Hz
50Hz
70Hz
56Hz 60Hz 72Hz 75Hz
75Hz
60Hz 70Hz 75Hz
60Hz
75Hz
1280x1024
1440x900
1600x900
60 Hz 70Hz 75Hz
60Hz
60Hz 75 Hz
Chapter 2.
2-7
Understanding power management
Power management is invoked when the computer recognizes that you have not used
your mouse or keyboard for a user-definable period. There are several states as
described in the table below.
For optimal performance, switch off your monitor at the end of each working day, or
whenever you expect to leave it unused for long periods during the day.
Table 2-4. Power indicator
Restoring
State
Power Indicator Screen
Operation
Compliance
On
Green
Normal
Blank
Standby/Suspend Amber
Press a key or
ENERGY STAR
move the mouse
There may be a
slight delay
before the image
reappears.
Note: Standby
also occurs if
there is no image
output to the
monitor.
Off
Off
Blank
Press the power ENERGY STAR
button
There may be a
slight delay
before the image
reappears.
Chapter 2.
2-8
Caring for your monitor
Be sure to turn off the power before you perform any maintenance on the monitor.
Do not:
•
•
•
Apply water or liquid directly to your monitor.
Use solvents or abrasives.
Use flammable cleaning materials to clean your monitor or any other electrical
equipment.
•
•
Touch the screen area of your monitor with sharp or abrasive items. This type of
contact may cause permanent damage to your screen.
Use any cleaner which contains an anti-static solution or similar additives. This
may harm the coating of the screen area.
Do:
•
Lightly dampen a soft cloth with water and use this to gently wipe the covers and
the screen.
•
Remove grease or finger marks with a damp cloth and a little mild detergent.
Detaching the monitor base and stand
step 1: Place the monitor on a soft and flat surface.
step 2: Remove the base and stand from the monitor,before disassembling the
stand,make sure the stand at level to push out the stand cover,then remove the three
screws.
Wall Mounting (Optional)
Refer to the instructions that come with the base mounting kit. To convert your LCD
display from a desk-mounted to a wall-mounted display, do the following:
Step 1: Verify that the Power button is turned Off, then disconnect the power cord.
Step 2: Lay the LCD display face down on a towel or blanket.
Chapter 2.
2-9
Step 3: Remove the base from the monitor, refer to "Detaching the monitor base and
stand".
Step 4: Attach the mounting bracket from the VESA compatible wall mounting kit
(100mm x100mm distance), VESA Mounting Screw M4 x 10 mm.
Step 5: Attach the LCD display to the wall, following the instructions in the wall-
mounting kit.
For use only with UL Listed Wall Mount Bracket with minimum weight/load: 8kg
Chapter 2.
2-10
Chapter 3. Reference information
This section contains monitor specifications, instructions to manually install the
monitor driver, troubleshooting information, and service information.
Monitor specifications
Table 3-1. Monitor specifications for type-model 60AB-AAR1-WW
Dimensions
Depth
160.7 mm (6.33 in.)
342.4 mm (13.48 in.)
Height
Width
Size
467.0 mm (18.39 in.)
19.5 in.
Panel
Backlight
LED
Aspect ratio
Tilt
16:9
Stand
Range: -5ï‚°ï€ ~ 22ï‚°
VESA mount
Image
Supported
100 mm x 100 mm (3.94 in. x 3.94 in.)
494.1 mm (19.5 in.)
Viewable image size
Maximum height
Maximum width
236.34 mm (9.30 in.)
433.92 mm (17.08 in.)
Pixel pitch
0.2712 mm (0.0107 in.)
Power input
Supply voltage
90-264VAC (100~240VAC+/-10%)
Max supply current
1.5 A
-
Power consumption
Normal operation
Standby/Suspend
Off
<19W
Note: Power consumption
figures are for the monitor
and the power supply
combined
<0.5W (Analog)
<0.5W at 100Vac & 240Vac
Note: without USB/
Webcam/external
speaker
Video input (Analog)
Input signal
Analog Direct Drive, 75 ohm 0.7V
Horizontal
addressability
1600 pixels (max)
--
Vertical addressability 900 lines (max)
Clock frequency
VESA DDC
205 MHz
CI
Communications
Chapter 3.
3-1
Table 3-1. Monitor specifications for type-model 60AB-AAR1-WW
Supported Display Modes
Horizontal frequency 30 kHz - 83 kHz
Vertical frequency
Native Resolution
Operating
50 Hz - 75 Hz
1600 x 900 at 60 Hz
0ï‚° to 45ï‚° C (32ï‚° to 113ï‚° F)
Temperature
Storage
-20ï‚° to 60ï‚° C (-4ï‚° to 140ï‚° F)
Shipping
-20ï‚° to 60ï‚° C (-4ï‚° to 140ï‚° F)
Humidity
Operating
10% to 80% non-condensing
Storage
5% to 95% non-condensing
5% to 95% non-condensing
Shipping
Chapter 3.
3-2
Troubleshooting
If you have a problem setting up or using your monitor, you might be able to solve it
yourself. Before calling your dealer or Lenovo, try the suggested actions that are
appropriate to your problem.
Table 3-2. Troubleshooting
Problem
Possible cause
Suggested action
Reference
The words "Out The system is set to a If you are replacing an
"Selecting a
of Range" are
shown on the
screen, and the
power indicator
is flashing white.
display mode which
is not supported by
the monitor.
and adjust the display
mode to within the
specified range for your
new monitor.
If using a Windows
system, restart the system
in safe mode, then select a
supported display mode
for your computer.
If these options do not
work, contact the Support
Center.
The image
quality is
unacceptable.
The video signal cable Be sure the signal cable is "Connecting and
is not connected with firmly plugged into the
the monitor or system system and monitor.
completely.
The color settings
may be incorrect.
Select another color
setting from the OSD
menu.
"Adjusting your
The automatic image Perform automatic image "Adjusting your
setup function was
not performed.
setup.
The power
•
•
•
The monitor’s
power switch is
not switched on.
•
Be sure the power
cord is connected
properly.
"Connecting and
indicator is not
lit and there is
no image.
The power cord is
loose or
disconnected.
•
•
•
•
•
Be sure the outlet has
power.
Power on the
monitor.
There is no power
at the outlet.
Try using another
power cord.
Try using another
electrical outlet.
Screen is blank
and power
indicator is
amber.
The monitor is in
Standby/Suspend
mode.
Press any key on the "Understanding
the mouse to restore management"on
operation.
•
Check the Power
Options settings on
your computer.
Chapter 3.
3-3
Table 3-2. Troubleshooting
Problem
Possible cause
Suggested action
Reference
The power
indicator is
The video signal cable Be sure the video cable is "Connecting and
is loose or
connected with the
amber, but there disconnected from the system properly.
is no image.
system or monitor.
The monitor
Adjust the brightness and "Adjusting your
brightness and
contrast are at the
lowest setting.
contrast setting on the
OSD menu.
One or more of
This is a characteristic If there are more than five Appendix A."Service
the pixels appear of the LCD
pixels missing, contact
discolored.
technology and is not the Support Center.
an LCD defect.
•
•
Fuzzy lines
in text or a
blurry
•
Image setup has
not been
optimized.
Adjust the resolution
settings on your system
to match the native
resolution for this
monitor: 1600 x900 at 60
Hz.
"Adjusting your
image.
•
Your system
Display
Properties setting
have not been
optimized.
Horizontal
or vertical
lines
through the
image.
Perform automatic image "Selecting a
setup does not help,
perform manual image
setup.
When working in the
native resolution, you
may find additional
improvements by
adjusting the Dots Per
Inch (DPI) setting on your
system.
See the Advanced
section of your
system’s display
properties.
Manual image setup
If automatic image setup does not establish the image that you prefer, perform
manual image setup.
Note: Have your monitor powered on for about 15 minutes, until the monitor warms
up.
1. Press
2. Use
3. Use
4. Use
at the bottom of the monitor to open the OSD menu.
to select and press to access.
to select manual and press to access.
to select Clock and Phase adjustment.
or
or
or
•
Clock (pixel frequency) adjusts the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the picture does not have the correct width.
•
Phase adjusts the phase of the pixel clock signal. With a wrong phase
adjustment, the picture has horizontal disturbances in light picture.
5. When the image no longer looks distorted, save the Clock and Phase adjustments.
6. Press to leave the OSD menu.
Chapter 3.
3-4
Manually installing the monitor driver
Below are steps for manually installing the monitor driver in Microsoft Windows 7,
Microsoft Windows 8, Microsoft Windows Vista.
Installing the monitor driver in Windows 7
To use the Plug and Play feature in Microsoft Windows 7, do the following:
Note: You must download file from the Reference and Driver CD to use the Plug and
Play feature in Windows 7.
1. Turn off the computer, all attached devices.
2. Ensure that the monitor is connected correctly.
3. Turn on the monitor and then the system unit. Allow your computer to start the
Windows 7 operating system.
4. Open the Display Properties window by clicking Start, Control Panel and
Hardware and Sound icon. and then clicking the Display icon.
5. Click the Change the display settings tab.
6. Click the Advanced Settings icon.
7. Click the Monitor tab.
8. Click the Properties button.
9. Click the Driver tab.
10. Click Update Driver, then click Browse the computer to find the driver program.
11. Select Pick from the list of device driver program on the computer.
12. Click the Hard Disk button. Click the Browse button and navigate to the
following directory:
X:\Monitor Drivers\Windows 7
(where X is the drive letter designator for the CD-ROM drive).
13. Select the "lenlt2013swA.inf" file and click the Open button. Click the OK button.
14. Select LEN LT2013swA and click Next. The files will be copied from the CD to
your hard disk drive.
15. Close all open windows and remove the CD.
16. Restart the system. The system will automatically select the maximum refresh
rate and corresponding Color Matching Profiles.
Note: On LCD monitors, unlike CRTs, a faster refresh rate does not improve display
quality. Lenovo recommends using either 1600 x900 at a refresh rate of 60 Hz, or 640 x
480 at a refresh rate of 60 Hz.
Chapter 3.
3-5
Installing the monitor driver in Windows 8
To use the Plug and Play feature in Microsoft Windows 8, do the following:
Note: You must download file from the Reference and Driver CD to use the Plug and
Play feature in Windows 8.
1. Turn off the computer, all attached devices.
2. Ensure that the monitor is connected correctly.
3. Turn on the monitor and then the system unit. Allow your computer to start the
Windows 8 operating system.
4. Open the Display Properties window by clicking Start, right-click, choose All
Applicaiton, inter Control Panel and Hardware and Sound icon. and then clicking
the Display icon.
5. Click the Change the display settings tab.
6. Click the Advanced Settings icon.
7. Click the Monitor tab.
8. Click the Properties button.
9. Click the Driver tab.
10. Click Update Driver, then click Browse the computer to find the driver program.
11. Select Pick from the list of device driver program on the computer.
12. Click the Hard Disk button. Click the Browse button and navigate to the
following directory:
X:\Monitor Drivers\Windows 8
(where X is the drive letter designator for the CD-ROM drive).
13. Select the "lenlt2013swA.inf" file and click the Open button. Click the OK button.
14. Select LEN LT2013swA and click Next. The files will be copied from the CD to
your hard disk drive.
15. Close all open windows and remove the CD.
16. Restart the system. The system will automatically select the maximum refresh
rate and corresponding Color Matching Profiles.
Note: On LCD monitors, unlike CRTs, a faster refresh rate does not improve display
quality. Lenovo recommends using either 1600 x900 at a refresh rate of 60 Hz, or 640 x
480 at a refresh rate of 60 Hz.
Chapter 3.
3-6
Installing the monitor driver in Windows Vista
To use the Plug and Play feature in Microsoft Windows Vista, do the following:
Note: You must download file from the Reference and Driver CD to use the Plug and
Play feature in Windows Vista.
1. Turn off the computer and all attached devices.
2. Ensure that the monitor is connected correctly.
3. Turn on the monitor and then the system unit. Allow your computer to start the
Windows Vista operating system.
4. Click Start, Control Panel and then click the Hardware and Sound icon.
5. Click the Personalization icon.
6. Click the Display Settings icon.
7. Click the Advanced Settings button.
8. Click the Monitor tab.
9. Click the Properties button.
10. Click the Driver tab.
11. Click Update Driver, then click Browse the computer to find the driver program.
12. Select Pick from the list of device driver program on the computer.
13. Click the Hard Disk button. Click the Browse button and navigate to the
following directory:
X:\Monitor Drivers\Windows Vista
(where X is the drive letter designator for the CD-ROM drive).
14. Select the "lenlt2013swA.inf" file and click the Open button. Click the OK button.
15. Select LEN LT2013swA and click Next. The files will be copied from the CD to
your hard disk drive.
16. Close all open windows and remove the CD.
17. Restart the system. The system will automatically select the maximum refresh
rate and corresponding Color Matching Profiles.
Note: On LCD monitors, unlike CRTs, a faster refresh rate does not improve display
quality. Lenovo recommends using either 1600 x900 at a refresh rate of 60 Hz, or 640 x
480 at a refresh rate of 60 Hz.
Getting further help
If you still can’t solve your problem, please contact the Lenovo Support Center. For
more information on contacting the Support Center, please see Appendix A."Service
Chapter 3.
3-7
Service information
Customer responsibilities
The warranty does not apply to a product which has been damaged due to accident,
misuse, abuse, improper installation, usage not in accordance with product
specifications and instructions, natural or personal disaster, or unauthorized
alterations, repairs or modifications.
The following are examples of misuse or abuse and not covered by warranty:
•
Images burned onto the screen of a CRT monitor. Burned image is preventable by
utilizing a moving screen saver or power management.
•
•
Physical damage to covers, bezel, base and cables.
Scratches or punctures on monitor screens.
Service parts
The following parts are for use by Lenovo service, or Lenovo aurthorized dealers, to
supprot the customer warranty. Parts are for service use only. The table below shows
information for model 60AB-AAR1-WW.
Table 3-3. List of service parts
FRU (FIELD
DESCRIPTION
Machine
Type/Model(MTM)
COLOR
REPLACEABLE UNIT)
PART NUMBER
03T8464
LT2013s Wide-FRU
Monitor
60AB
Raven
Black
03X8000(Pick up
from LT2013p)
LT2013s Wide-Analog 60AB
cable (1.8m, RoHS)
Raven
Black
03T8465
LT2013sWide-FRU
Stand and Base
60AB
Raven
Black
Chapter 3.
3-8
Appendix A. Service and Support
The following information describes the technical support that is available for your
product, during the warranty period or throughout the life of your product. Refer to
the Lenovo Limited Warranty for a full explanation of Lenovo warranty terms.
Registering your option
Register to receive product service and support updates, as well as free and
discounted computer accessories and content. Go to:
Online technical support
Online technical support is available during the lifetime of a product at:
Product replacement assistance or exchange of defective components also is available
during the warranty period. In addition, if your option is installed in a Lenovo
computer, you might be entitled to service at your location. A Lenovo technical
support representative can help you determine the best alternative.
Telephone technical support
Installation and configuration support through the Customer Support Center will be
available until 90 days after the option has been withdrawn from marketing. After
that time, the support is cancelled, or made available for a fee, at Lenovo’s discretion.
Additional support is also available for a nominal fee.
Before contacting a Lenovo technical support representative, please have the
following information available: option name and number, proof of purchase,
computer manufacturer, model, serial number and manual, the exact wording of any
error message, description of the problem, and the hardware and software
configuration information for your system.
Your technical support representative might want to walk you through the problem
while you are at your computer during the call.
Telephone numbers are subject to change without notice. The most up-to-date
telephone list for Lenovo Support is always available at:
Country or Region
Telephone Number
Africa
Africa: +44 (0)1475-555-055
South Africa: +27-11-3028888 and 0800110756
Central Africa: Contact the nearest Lenovo
Business Partner
Argentina
Australia
Austria
0800-666-0011 (Spanish)
131-426 (English)
Warranty service and support: 01-211-454-610 (German)
Appendix A.
A-1
Country or Region
Belgium
Telephone Number
Warranty service and support: 02-225-3611 (Dutch, French)
0800-10-0189 (Spanish)
Bolivia
Brazil
Sao Paulo region: (11) 3889-8986
Outside Sao Paulo region: 0800-701-4815
(Brazilian Portuguese)
Brunei
801-1041 (English, Bahasa Melayu)
Canada
Toronto: 416-383-3344
Outside Toronto: 1-800-565-3344
(English, French)
Chile
Toll Free: 188-800-442-488
800-361-213
(Spanish)
China
86-10-58851110
800-990-8888
(Mandarin)
China
(Hong Kong S.A.R.)
ThinkCentre® Commercial PC: 8205-0333
Multimedia Home PC: 800-938-228
(Cantonese, English, Mandarin)
China
(Macau S.A.R.)
ThinkCentre Commercial PC: 795-9892
Multimedia Home PC: 0800-336
(Cantonese, English, Mandarin)
Colombia
Costa Rica
Croatia
1-800-912-3021 (Spanish)
0-800-011-1029 (Spanish)
0800-0426
Cyprus
+357-22-841100
Czech Republic
Denmark
Dominican Republic
Ecuador
+420-2-7213-1316
Warranty service and support: 7010-5150 (Danish)
1-866-434-2080 (Spanish)
1-800-426911 (Spanish)
+202-35362525
Egypt
El Salvador
Estonia
800-6264 (Spanish)
+372 6776793
+372 66 00 800
Finland
France
Warranty service and support: +358-800-1-4260 (Finnish)
Warranty service and support (hardware): 0810-631-213
Warranty service and support (software): 0810-631-020
(French)
Germany
Greece
Warrantyserviceandsupport:01805 004618 (German)
+30-210-680-1700
Guatemala
Honduras
1800-624-0051 (Spanish)
Tegucigalpa: 232-4222
San Pedro Sula: 552-2234
(Spanish)
Appendix A.
A-2
Country or Region
Telephone Number
Hungary
+36-1-382-5716
+36-1-382-5720
(English, Hungarian)
India
1800-425-2666
+91-80-2535-9182
(English)
Indonesia
021 5238 823
Local number only: 001-803-606-282
DID (Direct Inward Dialing): +603 8315 6859
(English, Bahasa Indonesia)
Ireland
Israel
Warranty service and support: 01-881-1444 (English)
Givat Shmuel Service Center: +972-3-531-3900
(Hebrew, English)
Italy
Warranty service and support: +39-800-820094 (Italian)
Japan
Toll Free: 0120-20-5550
International: +81-46-266-4716
The above numbers will be answered with a Japanese language
voice prompt. For telephone support in English, please wait for the
Japanese voice prompt to end, and an operator will answer. Please
say "English support please," and your call will be transferred to
an English-speaking operator.
PC software: 0120-558-695
Overseas calls: +81-44-200-8666
(Japanese)
Korea
1588-6782 (Korean)
+371 7070360
Latvia
Lithuania
Luxembourg
Malaysia
+370 5 278 66 00
+352-360-385-343 (French)
Local number only: 1800-88-1889
DID: +603 8315 6855
(English, Bahasa Melayu)
Malta
+35621445566
Mexico
001-866-434-2080 (Spanish)
+44 (0)1475-555-055
Middle East
Netherlands
New Zealand
Nicaragua
Norway
+31-20-514-5770 (Dutch)
0800-733-222 (English)
001-800-220-1830 (Spanish)
Warranty service and support: 8152-1550 (Norwegian)
Panama
Lenovo Customer Support Center: 001-866-434-2080 (Toll Free)
206-6047 (Spanish)
Peru
0-800-50-866 (Spanish)
Philippines
Poland
1800-1601-0033 (English, Filipino)
+48-22-878-6999 (Polski)
Portugal
+351-21-892-7046 (Portuguese)
Appendix A.
A-3
Country or Region
Romania
Telephone Number
+4-021-224-4015
Russia
Moscow: +7-(495)-258-6300
Toll Free: +8-800-200-6300
(Russian)
Singapore
Local number only: 800-6011-343
DID: +603 8315 6859 (English)
Slovakia
Slovenia
Spain
+421-2-4954-5555
+386-1-200-50-60 (Slovenian)
91-714-7983
0901-100-000
(Spanish)
Sri Lanka
+9411 2493547
+9411 2493548
(English)
Sweden
Warranty service and support: 077-117-1040 (Swedish)
Switzerland
Warranty service and support: 0800-55-54-54
(German, French, Italian)
Taiwan
886-2-8723-9799
0800-000-700
(Mandarin)
Thailand
Local number only: 1-800-060-066
66 2273 4088
DID: +603 8315 6857 (Thai, English)
Turkey
0212 336 03 66 , 00800 448 825 165 (Turkish)
Standard warranty support: 08705-500-900 (English)
1-800-426-7378 (English)
United Kingdom
United States
Uruguay
000-411-005-6649 (Spanish)
Venezuela
Vietnam
0-800-100-2011 (Spanish)
For Northern Area and Hanoi City:
844 3 946 2000 or 844 3 942 6457
For Southern Area and Ho Chi Minh City:
848 3 829 5160 or 844 3 942 6457
(Vietnamese, English)
Appendix A.
A-4
Appendix B. Notices
Lenovo may not offer the products, services, or features discussed in this document in all
countries. Consult your local Lenovo representative for information on the products and
services currently available in your area. Any reference to a Lenovo product, program, or
service is not intended to state or imply that only that Lenovo product, program, or service
may be used. Any functionally equivalent product, program, or service that does not infringe
any Lenovo intellectual property right may be used instead.
However, it is the user 's responsibility to evaluate and verify the operation of any other
product, program, or service.
Lenovo may have patents or pending patent applications covering subject matter described in
this document. The furnishing of this document does not give you any license to these patents.
You can send license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimer of
express or implied warranties in certain transactions, therefore, this statement may not apply
to you.
This information could include technical inaccuracies or typographical errors. Changes are
periodically made to the information herein; these changes will be incorporated in new editions
of the publication. Lenovo may make improvements and/or changes in the product(s) and/or
the program(s) described in this publication at any time without notice.
The products described in this document are not intended for use in implantation or other life
support applications where malfunction may result in injury or death to persons. The
information contained in this document does not affect or change Lenovo product
specifications or warranties. Nothing in this document shall operate as an express or implied
license or indemnity under the intellectual property rights of Lenovo or third parties. All
information contained in this document was obtained in specific environments and is presented
as an illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those Web
sites. The materials at those Web sites are not part of the materials for this Lenovo
product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled environment.
Therefore, the result obtained in other operating environments may vary
significantly. Some measurements may have been made on development-level
systems and there is no guarantee that these measurements will be the same on
generally available systems. Furthermore, some measurements may have been
estimated through extrapolation. Actual results may vary. Users of this document
should verify the applicable data for their specific environment.
Appendix B.
B-1
Recycling information
Lenovo encourages owners of information technology (IT) equipment to responsibly recycle
their equipment when it is no longer needed. Lenovo offers a variety of programs and services
to assist equipment owners in recycling their IT products. For information on recycling
Lenovo products, go to:
Collecting and recycling a disused Lenovo computer or monitor
If you are a company employee and need to dispose of a Lenovo computer or monitor that is
the property of the company, you must do so in accordance with the Law for Promotion of
Effective Utilization of Resources. Computers and monitors are categorized as industrial waste
and should be properly disposed of by an industrial waste disposal contractor certified by a
local government. In accordance with the Law for Promotion of Effective Utilization of
Resources, Lenovo Japan provides, through its PC Collecting and Recycling Services, for the
collecting, reuse, and recycling of disused computers and monitors. For details, visit the
Promotion of Effective Utilization of Resources, the collecting and recycling of home-used
computers and monitors by the manufacturer was begun on October 1, 2003. This service is
provided free of charge for home-used computers sold after October 1, 2003. For details, visit
Disposing of Lenovo computer components
Some Lenovo computer products sold in Japan may have components that contain heavy
metals or other environmental sensitive substances. To properly dispose of disused
components, such as a printed circuit board or drive, use the methods described above for
collecting and recycling a disused computer or monitor.
Trademarks
The following terms are trademarks of Lenovo in the United States, other countries,
or both:
Lenovo
The Lenovo logo
ThinkCenter
ThinkPad
ThinkVision
Microsoft, Windows, and Windows NT are trademarks of the Microsoft group of
companies.
Other company, product, or service names may be trademarks or service marks of
others.
Appendix B.
B-2
|
Iiyama PROLITE E2001WSV User Manual
KitchenAid Convection Oven KCO222 User Manual
KitchenAid Cooktop KGCV566 User Manual
Konftel 300M Cellular Conference Phone 300M User Manual
Lenovo Computer Monitor 9487 User Manual
Motorola D1110 User Manual
Panasonic CT 32SX31CE User Manual
Philips 107S5 User Manual
Philips 190S8FS User Manual
Philips Kala 200 User Manual