TK-2180/ TK-3180
VHF FM TRANSCEIVER/
UINHFSFMTTRRAUNSCCETIVIEOR N MANUAL
ÉMETTEUR-RÉCEPTEUR FM VHF/
ÉMETTEUR-RÉCEPTEUR FM UHF
MODE D’EMPLOI
TRANSCEPTOR DE FM VHF/
TRANSCEPTOR DE FM UHF
MANUAL DE INSTRUCCIONES
RICETRASMETTITORE FM VHF/
RMICAETNRAUSMAETLTEITORDEIFMISUHTFRUZIONI
VHF-FM-TRANSCEIVER/
UBHEF-FDMI-TERANNSUCNEIVGERSANLEITUNG
VHF FM ZENDONTVANGER/
UGHFEFBMRZEUNDIOKNTSVAANAGENR WIJZING
© B62-1760-00 (E)
09 08 07 06 05 04 03 02 01 00
THANK YOU
We are grateful you chose KENWOOD for your land mobile radio
applications. We believe this easy-to-use transceiver will provide
dependable communications to keep personnel operating at peak
efficiency.
KENWOOD transceivers incorporate the latest in advanced
technology. As a result, we feel strongly that you will be pleased
with the quality and features of this product.
MODELS COVERED BY THIS MANUAL
• TK-2180: VHF FM Transceiver
• TK-3180: UHF FM Transceiver
NOTICES TO THE USER
N
Government law prohibits the operation of unlicensed radio
transmitters within the territories under government control.
N
N
Illegal operation is punishable by fine and/or imprisonment.
Refer service to qualified technicians only.
SAFETY: It is important that the operator is aware of and
understands hazards common to the operation of any transceiver.
PRECAUTIONS
•
Do not charge the transceiver and battery pack when they are
wet.
•
Ensure that there are no metallic items located between the
transceiver and the battery pack.
•
•
Do not use options not specified by KENWOOD.
If the die-cast chassis or other transceiver part is damaged, do
not touch the damaged parts.
•
•
If a headset or headphone is connected to the transceiver, reduce
the transceiver volume. Pay attention to the volume level when
turning the squelch off.
Do not place the microphone cable around your neck while near
machinery that may catch the cable.
•
•
•
Do not place the transceiver on unstable surfaces.
Ensure that the end of the antenna does not touch your eyes.
When the transceiver is used for transmission for many hours, the
radiator and chassis will become hot. Do not touch these
locations when replacing the battery pack.
•
Do not immerse the transceiver in water.
i
Turn the transceiver power off in the following locations:
•
In explosive atmospheres (inflammable gas, dust particles,
metallic powders, grain powders, etc.).
•
•
•
•
While taking on fuel or while parked at gasoline service stations.
Near explosives or blasting sites.
In aircrafts.
In medical institutions or near persons using pacemakers.
•
•
Do not disassemble or modify the transceiver for any reason.
Do not place the transceiver on or near airbag equipment while
the vehicle is running. When the airbag inflates, the transceiver
may be ejected and strike the driver or passengers.
•
•
Do not transmit while touching the antenna terminal or if any
metallic parts are exposed from the antenna covering.
Transmitting at such a time may result in a high-frequency burn.
If an abnormal odor or smoke is detected coming from the
transceiver, switch the transceiver power off immediately, remove
the battery pack from the transceiver, and contact your
KENWOOD dealer.
•
•
Use of the transceiver while you are driving may be against traffic
laws. Please check and observe the vehicle regulations in your
area.
Do not expose the transceiver to extremely hot or cold
conditions.
ii
CONTENTS
UNPACKING AND CHECKING EQUIPMENT ............................. 1
SUPPLIED ACCESSORIES ....................................................... 1
PREPARATION .............................................................. 2
BATTERY PACK PRECAUTIONS .................................................. 2
INSTALLING/ REMOVING THE (OPTIONAL) BATTERY PACK ......................... 7
INSTALLING THE (OPTIONAL) ANTENNA .......................................... 8
INSTALLING THE BELT CLIP .................................................... 8
INSTALLING THE CAP OVER THE UNIVERSAL CONNECTOR .......................... 9
INSTALLING THE (OPTIONAL) SPEAKER/ MICROPHONE OR HEADSET ............... 9
GETTING ACQUAINTED .................................................. 10
DISPLAY ................................................................... 12
PROGRAMMABLE FUNCTIONS......................................... 14
BASIC OPERATIONS ..................................................... 16
OVERVIEW ................................................................. 16
SWITCHING POWER ON/ OFF............................................... 16
ADJUSTING THE VOLUME .................................................... 17
SELECTING A ZONE AND CHANNEL ............................................ 17
TRANSMITTING .............................................................. 18
RECEIVING ................................................................. 18
CONVENTIONAL SCAN................................................... 19
ADD TO SCAN/ DELETE FROM SCAN .......................................... 19
SCAN REVERT .............................................................. 20
PRIORITY SCAN ............................................................. 20
QUIET TALK (QT)/ DIGITAL QUIET TALK (DQT) ...................... 21
OPERATOR SELECTABLE TONE (OST) ........................................ 21
5-TONE SIGNALING ...................................................... 22
MAKING A SELCALL (SELECTIVE CALL) ....................................... 22
TRANSMITTING A STATUS MESSAGE .......................................... 23
RECEIVING SELCALLS AND STATUS MESSAGES ................................. 24
REVIEWING MESSAGES IN THE QUEUE MEMORY ............................... 25
iii
FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION.......... 26
SELCALL (SELECTIVE CALLING) .............................................. 26
STATUS MESSAGE .......................................................... 27
SHORT MESSAGES .......................................................... 29
LONG MESSAGES ........................................................... 29
DTMF (DUAL TONE MULTI FREQUENCY) CALLS .................... 30
MANUAL DIALING ........................................................... 30
AUTODIAL .................................................................. 30
REDIAL .................................................................... 30
CONNECT/ DISCONNECT IDS ................................................. 31
DTMF SIGNALING ......................................................... 31
STUN ...................................................................... 31
VOICE OPERATED TRANSMISSION (VOX)............................ 32
EMERGENCY CALLS ..................................................... 34
ADVANCED OPERATIONS ............................................... 35
SELECTING A TRANSMIT POWER .............................................. 35
TALK AROUND .............................................................. 35
MONITOR/ SQUELCH OFF .................................................... 36
KEY LOCK .................................................................. 37
SCRAMBLER ................................................................ 37
CLOCK ..................................................................... 38
TRANSCEIVER BACKLIGHT .................................................... 38
BACKGROUND OPERATIONS ........................................... 39
TIME-OUT TIMER (TOT) .................................................... 39
BUSY CHANNEL LOCKOUT (BCL) ............................................ 39
BATTERY SAVER ............................................................ 39
BATTERY POWER INDICATOR ................................................. 40
SIGNAL STRENGTH INDICATOR ................................................ 40
BEGINNING/ END OF TRANSMIT SIGNAL ....................................... 40
VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT ................. 41
VOICE RECORDER ........................................................... 41
VOICE GUIDE ............................................................... 43
iv
UNPACKING AND CHECKING EQUIPMENT
Note: The following unpacking instructions are for use by your
KENWOOD dealer, an authorized KENWOOD service facility, or the
factory.
Carefully unpack the transceiver. We recommend that you
identify the items listed in the following table before discarding
the packing material. If any items are missing or have been
damaged during shipment, file a claim with the carrier
immediately.
SUPPLIED ACCESSORIES
Item
Part Number
J29-0710-XX
N30-3008-XX
B09-0625-XX
N08-0548-XX
B62-1760-XX
Quantity
Belt clip
1
2
1
1
1
Screw for belt clip
Univeral connector cap
Screw for connector cap
Instruction manual
Belt clip + screws
Universal connector
cap + screw
1
PREPARATION
BATTERY PACK PRECAUTIONS
Do not use battery packs or battery chargers not
recommended by KENWOOD.
N
N
Do not recharge the battery pack if it is already fully charged.
Doing so may cause the life of the battery pack to shorten or the
battery pack may be damaged.
After charging the battery pack, disconnect it from the charger. If
the charger power is reset (turned ON after being turned OFF),
recharging will start again and the battery pack will become
overcharged.
N
N
Do not use the transceiver while charging the battery pack. We
recommend you switch the transceiver power OFF while
charging is taking place.
Do not charge the battery pack when the battery pack or
transceiver is wet, to avoid the risk of fire or damage. Wipe the
water from thebattery pack or transceiver using a dry cloth before
charging.
N
N
Do not short the battery terminals or dispose of the battery by
fire.
Never attempt to remove the casing from the battery pack.
I CHARGING THE BATTERY PACK
For charging procedures, refer to the battery charger
Instruction Manual.
2
Information concerning the (optional) Li-ion battery pack:
The battery pack includes flammable objects such as organic solvent.
Mishandling may cause the battery to rupture producing flames or
extreme heat, deteriorate, or cause other forms of damage to the battery.
Please observe the following prohibitive matters.
DANGER
•
•
Do not disassemble or reconstruct battery!
The battery pack has a safety function and protection circuit to
avoid danger. If they suffer serious damage, the battery may
generate heat or smoke, rupture, or burst into flame.
Do not short-circuit the battery!
Do not join the + and – terminals using any form of metal (such as
a paper clip or wire). Do not carry or store the battery pack in
containers holding metal objects (such as wires, chain-necklace or
hairpins). If the battery pack is short-circuited, excessive current
will flow and the battery may generate heat or smoke, rupture, or
burst into flame. It will also cause metal objects to heat up.
•
•
Do not incinerate or apply heat to the battery!
If the insulator is melted, the gas release vent or safety function is
damaged, or the electrolyte is ignited, the battery may generate
heat or smoke, rupture, or burst into flame.
Do not use or leave the battery near fires, stoves, or other
heat generators (areas reaching over 80°C)!
If the polymer separator is melted due to high temperature, an
internal short-circuit may occur in the individual cells and the
battery may generate heat or smoke, rupture, or burst into flame.
•
•
Do not immerse the battery in water or get it wet by other
means!
If the battery’s protection circuit is damaged, the battery may
charge at extreme current (or voltage) and an abnormal chemical
reaction may occur. The battery may generate heat or smoke,
rupture, or burst into flame.
Do not charge the battery near fires or under direct sunlight!
If the battery’s protection circuit is damaged, the battery may
charge at extreme current (or voltage) and an abnormal chemical
reaction may occur. The battery may generate heat or smoke,
rupture, or burst into flame.
3
•
Use only the specified charger and observe charging
requirements!
If the battery is charged in unspecified conditions (under high
temperature over the regulated value, excessive high voltage or
current over regulated value, or with a remodelled charger), it may
overcharge or an abnormal chemical reaction may occur. The
battery may generate heat or smoke, rupture, or burst into flame.
•
•
Do not pierce the battery with any object, strike it with an
instrument, or step on it!
This may break or deform the battery, causing a short-circuited.
The battery may generate heat or smoke, rupture, or burst into
flame.
Do not jar or throw the battery!
An impact may cause the battery to leak, generate heat or
smoke, rupture, and/or burst into flame. If the battery’s protection
circuit is damaged, the battery may charge at an abnormal
current (or voltage), and an abnormal chemical reaction may
occur. The battery may generate heat or smoke, rupture, or burst
into flame.
•
•
Do not use the battery pack if it is damaged in any way!
The battery may generate heat or smoke, rupture, or burst into
flame.
Do not solder directly onto the battery!
If the insulator is melted or the gas release vent or safety function
is damaged, the battery may generate heat or smoke, rupture, or
burst into flame.
•
•
Do not reverse the battery polarity (and terminals)!
When charging a reversed battery, an abnormal chemical
reaction may occur. In some cases, an unexpected large amount
of current may flow upon discharging. The battery may generate
heat or smoke, rupture, or burst into flame.
Do not reverse-charge or reverse-connect the battery!
The battery pack has positive and negative poles. If the battery
pack does not smoothly connect with a charger or operating
equipment, do not force it; check the polarity of the battery. If the
battery pack is reverse-connected to the charger, it will be
reverse-charged and an abnormal chemical reaction may occur.
The battery may generate heat or smoke, rupture, or burst into
flame.
4
•
Do not touch a ruptured and leaking battery!
If the electrolyte liquid from the battery gets into your eyes, wash
your eyes out with fresh water as soon as possible, without
rubbing your eyes. Go to the hospital immediately. If left
untreated, it may cause eye-problems.
•
•
•
Do not charge the battery for longer than the specified time!
If the battery pack has not finished charging even after the
regulated time has passed, stop it. The battery may generate
heat or smoke, rupture, or burst into flame.
Do not place the battery pack into a microwave or high
pressure container!
The battery may generate heat or smoke, rupture, or burst into
flame.
Keep ruptured and leaking battery packs away from fire!
If the battery pack is leaking (or the battery emits a bad odor),
immediately remove it from flammable areas. Electrolyte leaking
from battery can easily catch on fire and may cause the battery to
generate smoke or burst into flame.
•
Do not use an abnormal battery!
If the battery pack emits a bad odor, appears to have different
coloring, is deformed, or seems abnormal for any other reason,
remove it from the charger or operating equipment and do not
use it. The battery may generate heat or smoke, rupture, or burst
into flame.
5
I USING THE LI-ION BATTERY PACK
•
Charge the battery pack before using it.
•
To keep the battery discharge at a minimum, remove the
battery pack from the equipment when it is not in use. Store
the battery pack in a cool and dry location.
•
When storing the battery pack for a long period:
1
2
3
Remove the battery pack from the equipment.
Discharge the battery pack, if possible.
Store the battery pack in a cool (below 25°C) and dry
location.
I CHARACTERISTICS OF THE LI-ION BATTERY PACK
•
•
•
•
As the battery pack is charged and discharged repeatedly, the
battery capacity decreases.
Even if the battery pack is unused, the battery pack
degrades.
It takes a longer time to charge the battery pack in cooler
areas.
The life of battery pack is shortened when it is charged and
discharged in hotter areas. When the battery pack is stored
in a hot location, the battery pack degrades quicker. Do not
leave the battery pack in vehicles or near heating appliances.
•
When the battery pack operating time becomes short, even if
it is fully charged, replace the battery pack. Continuing to
charge and discharge the battery pack may result in
electrolyte leakage.
6
INSTALLING/ REMOVING THE (OPTIONAL) BATTERY PACK
1
Match the guides of the
battery pack with the
corresponding grooves on the
upper rear of the transceiver,
then firmly press the battery
pack to lock it in place.
2
3
Lock the safety catch to
prevent accidentally pressing
the release latch and
removing the battery pack.
To remove the battery pack,
lift the safety catch, press the
release latch, then pull the
battery pack away from the
transceiver.
Note:
N
To lift the battery pack safety catch, use a piece of hardened
plastic or metal, such as a screwdriver, that is no more than 6 mm
wide and 1 mm thick. It is imperative that you place the
implement under only the lip of the safety catch so that you do
not damage the release latch.
N
N
Before charging a battery pack that is attached to the transceiver,
ensure that the safety catch is firmly closed.
While operating the transceiver using a Li-ion or Ni-MH battery
pack in areas with an ambient temperature of –10°C and lower,
operating time may be shortened.
7
INSTALLING THE (OPTIONAL) ANTENNA
Screw the antenna into the
connector on the top of the
transceiver by holding the
antenna at its base and turning it
clockwise until secure.
Note: The antenna is neither a
handle, a key ring retainer, nor a
speaker/ microphone attachment
point. Using the antenna in these
ways may damage the antenna and
degrade your transceiver’s
MIC
S
A
performance.
<
B
C
1
>
INSTALLING THE BELT CLIP
If necessary, attach the belt clip
using the two supplied
3 x 8 mm screws.
Note: If the belt clip is not installed,
its mounting location may get hot
during continuous transmission or
when left sitting in a hot
environment.
Do not use glue which is designed to prevent screw loosening when
installing the belt clip, as it may cause damage to the transceiver.
Acrylic ester, which is contained in these glues, may crack the
transceiver’s back panel.
8
INSTALLING THE CAP OVER THE UNIVERSAL CONNECTOR
If you are not using an optional
speaker/ microphone or headset,
install the cap over the universal
connector using the supplied
4 x 6 mm screw. Ensure that the
cap fits tightly over the connector.
MIC
S
A
<
B
C
1
>
INSTALLING THE (OPTIONAL) SPEAKER/ MICROPHONE OR HEADSET
1
Insert the guide of the
speaker/ microphone
connector into the
groove of the universal
connector.
2
Secure the connector
in place using the
attached screw.
MIC
Note: When not using an
optional speaker/
microphone or headset,
install the cap over the
universal connector.
S
A
<
B
C
1
>
2ABC
4 GHI
3DEF
5JKL
8 TUV
7
6
MNO
PQRS
9WXYZ
0
#
9
GETTING ACQUAINTED
Microphone
Speaker
MIC
>
S
<
B
A
C
DEF
1
ABC
3
2
5
8
GHI
MNO
WXYZ
#
4
JKL
TUV
6
7PQRS
9
0
q Antenna connector
Connect an antenna here {page 8}.
w Selector
Rotate to activate its programmable function {page 14}.
10
e Power switch/ Volume control
Turn clockwise to switch ON the transceiver. Rotate to
adjust the volume. Turn counterclockwise fully to switch
OFF the transceiver.
r Transmit/ Busy/ Call indicator
This LED lights red during transmission, green while
receiving a call, and orange when receiving an encoded
call (i.e. 5-tone, DTMF signaling, etc.).
t Auxiliary (orange) key
Press to activate its programmable function {page 14}.
y Safety Catch
Lock this catch to avoid accidentally pressing the release
latch and removing the battery pack {page 7}.
u Release Latch
Press the release latch to unlock and remove the battery
pack {page 7}.
i Side 1 key
Press to activate its programmable function {page 14}.
o PTT (Push-To-Talk) switch
Press this switch, then speak into the microphone to call a
station.
!
0
0
1
2
0
0
Side 2 key
Press to activate its programmable function {page 14}.
!
1
1
1
1
S, A, <B, and C> keys
Press to activate their programmable functions {page 14}.
!
2
2
2
2
DTMF keypad
Press the keys on the keypad to make DTMF calls
{page 30} or to activate their programmable functions
{page 14}.
!
3
3
3
3
3
Universal connector
Connect a speaker/ microphone or headset here {page 9}.
Otherwise, keep the supplied cap in place.
11
DISPLAY
Indicator
Description
Displays the zone and channel numbers.
Your dealer can program zone and channel
names with up to 12 characters, in place
of numbers. Also displays received 5-tone
and FleetSync messages.
Displays the zone and channel numbers.
Also displays list numbers for Operator
Selectable Tones.
Displays the strength of received signals.
An antenna and all 3 strength bars
represents strong signals while the antenna
by itself (no strength bars) represents weak
signals.
Appears when Monitor or Squelch Off is
activated.
Appears when the Talk Around function
has been activated.
Appears when you are using Scan mode or
while the selected zone is a Voting or Free
Channel Call zone.
Flashes when you receive a message.
Lights when a message is stored in the
queue memory.
12
Indicator
Description
Appears when the selected channel is
programmed as priority. represents
Priority Channel 1, represents Priority
Channel 2, and represents Priority
Channels 1 and 2.
This icon is not used on this transceiver.
Appears when the selected channel is
using low transmit power.
Appears when the scrambler function is
activated.
Displays the battery power status as high,
sufficient, low, or very low.
Appears when the selected zone is added
to the scanning sequence.
Appears when the auto recording function
on the VGS-1 option is activated.
Appears when an Auto Reply Message on
the VGS-1 option is activated.
Appears when the selected channel is
added to the scanning sequence.
Appears when the VOX function has been
activated.
Appears when the AUX function has been
activated.
Appears when the OST function has been
activated.
13
PROGRAMMABLE FUNCTIONS
The Auxiliary, Side 1, Side 2, S, A, <B, and C> keys, and the
DTMF keypad {pages 10 and 11} can be programmed with the
functions listed below. Please contact your dealer for further
details on these functions.
Note: The selector can be programmed as either CH/GID Up/Down
or Zone Up/Down.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Auto Reply Message 1, 2
Autodial
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Key Lock
Lamp
Autodial Programming
AUX
Lone Worker
Low Transmission Power
Monitor
Call 1 ~ Call 6
CH/GID Down
Monitor Momentary
None
CH/GID Down (Continuous)
CH/GID Recall
CH/GID Up
OST
Playback 2
CH/GID Up (Continuous)
Channel Entry
Priority Channel Select
Queue
Receive Entry 3
Clock
Digit 1x Down 3
Digit 10x Down 3
Digit 1x Up 3
Scan
Scan Delete/Add
Scrambler
Digit 10x Up 3
Scrambler Code
Selcall
Direct CH/GID 1 ~ 5
Direct CH/GID 1 ~ 5 Select
Display Character
Emergency 4
Selcall + Status
Speaker Attenuation 5
Squelch Level
Squelch Off
Squelch Off Momentary
Status
Fixed Volume
Function
Home CH/GID
Home CH/GID Select
Talk Around
14
•
•
•
•
Transceiver Password
Voice Memo 2
VOX
•
•
•
•
Zone Down
Zone Down (Continuous)
Zone Up
Zone Delete/Add
Zone Up (Continuous)
1
2
“Auto Reply Message” can be used only for FleetSync.
“Auto Reply Message”, “Playback”, and “Voice Memo” can be
programmed only when the optional VGS-1 board has been
installed.
3
4
5
“Digit 1x Down”, “Digit 10x Down”, “Digit 1x Up”, “Digit 10x Up”,
and “Receive Entry” can be programmed only for 5-tone calls.
“Emergency” can be programmed only on the Auxiliary (orange) key
and the PF1 key of the optional KMC-25 speaker/ microphone.
“Speaker Attenuation” can be programmed only on the PF1 and
PF2 keys of the optional KMC-25 speaker/ microphone.
15
BASIC OPERATIONS
OVERVIEW
Your dealer can program your transceiver with Conventional,
Voting, Voting with Signaling, and Free Channel Call zones.
The transceiver can handle up to 128 zones with up to 250
channels in each zone and a total combined maximum of 512
channels. Zones, channels, and their functions are
programmed by your dealer.
SWITCHING POWER ON/ OFF
Turn the Power switch/ Volume control clockwise to switch
the transceiver ON.
•
•
A beep sounds and the display momentarily lights up.
If the Transceiver Password function is programmed, “
appears on the display. You must enter the password to unlock
”
the transceiver. Refer to “Transceiver Password”, below.
Turn the Power switch/ Volume control counterclockwise to
switch the transceiver OFF.
I TRANSCEIVER PASSWORD
To enter the password using the DTMF keypad:
1
Press the DTMF keys corresponding to the password
digits.
•
Press the A or # key to delete an incorrect character.
Press and hold the A or # key to delete all entered
characters.
2
Press the S or key to confirm the password.
•
If you enter an incorrect password, an error tone sounds
and the transceiver remains locked.
16
To enter the password without using the DTMF keypad:
1
2
Rotate the selector to select a digit.
Press the C> key to accept the entered digit and move
to the next digit.
•
Press the A or # key to delete an incorrect character.
Press and hold the A or # key to delete all entered
characters.
3
Press the S key to confirm the password.
•
If you enter an incorrect password, an error tone sounds
and the transceiver remains locked.
ADJUSTING THE VOLUME
Rotate the Power switch/ Volume control to adjust the
volume. Clockwise increases the volume and counter-
clockwise decreases it.
SELECTING A ZONE AND CHANNEL
Select the desired zone using the selector or the keys
programmed as Zone Up/ Zone Down.
Select the desired channel using the selector or the keys
programmed as CH/GID (Channel/ Group ID) Up/ CH/GID
(Channel/ Group ID) Down.
Names can be programmed for zones and channels with up to
12 characters each. However, to fit on the display, names will
be abbreviated. Your dealer can set the zone name to a
length of 0 to 12 digits. Channel names will shorten
appropriately, to fit in the 12-digit display.
For example, if the channel name is “–CHANNEL1–” and the
zone name is “KENWOOD”, and your dealer sets the zone
name to 3-digits, the following display will appear:
17
TRANSMITTING
1
3
4
Select the desired zone and channel using the selector
and the Zone or CH/GID keys.
•
In Voting, Voting with Signaling, and Free Channel Call
zones, the channel is seleted automatically.
In Conventional zones, press the key programmed as
Monitor or Squelch Off to check whether or not the
channel is free.
•
If the channel is busy, wait until it becomes free.
Press the PTT switch and speak into the microphone.
Release the PTT switch to receive.
•
•
•
For best sound quality at the receiving station, hold the
microphone approximately 1.5 inches (3 ~ 4 cm) from your
mouth.
In Voting and Voting with Signaling zones, the transceiver will
search for the closest repeater and transmit using that
repeater’s frequency.
In Free Channel Call zones, the transceiver will search for a
free channel and will begin transmitting on that channel.
RECEIVING
1
Select the desired zone and channel using the selector
and the Zone or CH/GID keys.
•
•
Alternatively, in Conventional zones, you can activate the
Scan function if desired.
In Voting and Voting with Signaling zones, the transceiver will
automatically search for the strongest signal and receive on
that frequency.
•
In Free Channel Call zones, the transceiver will automatically
search for any signal and will receive on that channel.
2
When you hear a caller’s voice, readjust the volume as
necessary.
18
CONVENTIONAL SCAN
If the Scan function is programmed, Conventional zones or
channels can be scanned by pressing the key programmed as
Scan. Scan can be used as either Single Scan or Multi Scan.
•
Single Scan monitors only the channels of the currently selected
zone, which have been added to the scanning sequence. If set
up to scan Priority channels, the Priority channels will be scanned
even if they are not within the currently selected zone.
•
Multi Scan monitors all channels of every zone, which have been
added to the scanning sequence.
To activate Scan, press the key programmed as Scan.
•
The
appear on the display.
The zone add indicator (
display when the selected zone is added to the scan sequence.
The channel add indicator ( ) will appear on the
icon and “
” or the revert zone and channel number
•
) will appear on the
display when the selected channel is added to the scan
sequence.
•
When a call is received, scanning stops and the zone and
channel digits appear. Press the PTT switch and speak into the
microphone to respond to the call. The transceiver will continue
scanning after a predetermined time delay if the PTT switch is
released and no further signal is received.
To stop scanning, press the Scan key again.
ADD TO SCAN/ DELETE FROM SCAN
Press the key programmed as Scan Delete/Add to add or
remove each channel to or from the scan sequence.
•
The channel add indicator (
display when the selected channel is added to the scan
sequence.
) will appear on the
Press the key programmed as Zone Delete/Add to add or
remove each zone to or from the scan sequence.
•
The zone add indicator (
display when the selected zone is added to the scan sequence.
) will appear on the
19
SCAN REVERT
You can select Revert zones and channels using the selector
and the Zone or CH/GID keys.
Eight types of Scan Reverts which can be programmed by
your dealer are available.
•
•
•
•
Last Called Revert: The last zone/ channel received is assigned
as the new revert zone and channel.
Last Used Revert: The last zone/ channel responded to is
assigned as the new revert zone and channel.
Selected: The last zone/ channel selected is assigned as the
new revert zone and channel.
Selected + Talkback: If the zone/ channel has been changed
during Scan, the newly selected zone/ channel is assigned as the
new revert zone and channel. The transceiver “talks back” on the
current receive channel.
•
•
Priority 1/ Priority 2: If your dealer has programmed a Priority
channel (either Priority 1 or Priority 2), this channel is the revert
zone and channel.
Priority 1 + Talkback/ Priority2 + Talkback: If your dealer has
programmed a Priority channel (either Priority 1 or Priority 2), this
channel is the revert zone and channel. The transceiver “talks
back” on the current receive channel.
PRIORITY SCAN
A Priority channel must be programmed in order for Priority
Scan to function.
The transceiver will automatically change to the Priority
channel when a signal is received on it, even if a signal is
being received on a normal channel.
•
•
•
The indicator represents the Priority 1 channel.
The indicator represents the Priority 2 channel.
The indicator represents both the Priority 1 and Priority 2
channel.
20
QUIET TALK (QT)/ DIGITAL QUIET TALK (DQT)
Your dealer may have programmed QT or DQT signaling on
your transceiver channels. A QT tone/ DQT code is a
sub-audible tone/code which allows you to ignore (not hear)
calls from other parties who are using the same channel.
When a channel is set up with a QT tone or DQT code, squelch
will open only when a call containing a matching tone or code
is received. Likewise, signals you transmit will be heard only
by parties whose QT/ DQT signaling matches your transceiver.
If a call containing a different tone or code is made on the
same channel you are using, squelch will not open and you
will not hear the call. Although it may seem like you have your
own private channel while using QT/ DQT, other parties can
still hear your calls if they set up their transceiver with the
same tone or code.
OPERATOR SELECTABLE TONE (OST)
You can change the preset encode and decode tones for the
selected channel. Your dealer can program up to 40 tones on
your transceiver.
To turn OST on or off, press the key programmed as OST.
•
The OST indicator (
this function is activated.
) appears on the display when
To change the preset encode/decode tones:
1
Press and hold the key programmed as OST.
•
The duration for holding the OST key is programmed by your
dealer.
•
The OST number and name appear on the display.
2
3
Rotate the selector, press the <B and C> keys, or enter
the list number directly using the DTMF keypad to select
your desired encode/decode pair.
Press the S or
key to accept the new setting and return
to normal operation.
21
5-TONE SIGNALING
5-tone Signaling is enabled or disabled by your dealer. This
function opens the squelch only when the transceiver receives
the 5 tones programmed in your transceiver. Transceivers
that do not transmit the correct tones will not be heard.
Note: Your transceiver functions include either 5-tone Signaling or
FleetSync {page 26}, but not both.
MAKING A SELCALL (SELECTIVE CALL)
A Selcall is a voice call to a particular station. To make a
Selcall:
1
2
Select your desired zone and channel.
Press the key programmed as Selcall or Selcall + Status
to enter Selcall Mode.
3
Rotate the selector or press the <B and C> keys to select
the ID of the station you want to call.
•
•
Alternatively, you can enter a station ID using the DTMF
keypad.
You can also enter digits by using the DTMF keypad or by
selecting digits with the selector. Before entering digits using
the DTMF keypad, enter Manual Input Mode by pressing and
holding the S key. When using the selector, rotate it to select
a digit. The cursor can be shifted to the left or right by
pressing the <B or C> key. Repeat this process until the
entire ID is entered.
4
Press the key programmed as Call 1 to Call 6 and begin
your call.
22
TRANSMITTING A STATUS MESSAGE
Status messages can contain up to 16 alphanumeric
characters. To transmit a Status message:
1
2
Select your desired zone and channel.
Press the key programmed as Status to enter Status
Mode or Selcall + Status to enter Selcall Mode.
•
When using the Status key to enter Status Mode, the station
ID is fixed and cannot be selected. Skip to step 5 to continue.
3
In Selcall Mode, rotate the selector or press the <B and
C> keys to select the ID of the station you want to call.
•
Alternatively, you can enter a station ID using the DTMF
keypad.
•
If Manual Input Mode is enabled, you can enter digits by
using the DTMF keypad or by selecting digits with the
selector. To enter Manual Input Mode, press and hold the S
key. When using the selector, rotate it to select a digit. The
cursor can be shifted to the left or right by pressing the <B or
C> key. Repeat this process until the entire ID is entered.
4
5
Press the S key to enter Status Mode.
Rotate the selector or press the <B and C> keys to select
the status ID you want to transmit.
•
•
Alternatively, you can enter the status ID using the DTMF
keypad.
If manual input mode is enabled, you can enter digits by
using the DTMF keypad or by selecting digits with the
selector. To enter manual input mode, press and hold the S
key. When using the selector, rotate it to select a digit. The
cursor can be shifted to the left or right by pressing the <B or
C> key. Repeat this process until the entire ID is entered.
6
Press the Call 1 to Call 6 key to initiate the Status call.
23
RECEIVING SELCALLS AND STATUS MESSAGES
When you receive a signal containing the correct tones,
squelch opens and you will hear the call.
•
•
The LED indicator flashes orange.
To mute the speaker after squelch opens, press the key
programmed as Monitor.
•
•
•
•
Your dealer can program the monitor function to close again after
a specific time period elapses.
If Transpond for 5-tone Signaling is programmed, an
acknowledgment signal is returned to the calling station.
If Call Alert for 5-tone Signaling is programmed, an alert tone will
sound when the correct tones are received.
Your dealer can program the transceiver to display the received
Selcall/Status.
To respond to the call, press the PTT switch and speak into
the microphone.
24
REVIEWING MESSAGES IN THE QUEUE MEMORY
A maximum of 15 received messages can be stored in the
Queue memory of your transceiver. Saved messages can be
viewed after reception. Depending on your dealer settings,
when the Queue memory is full, either the oldest message will
be erased when a new message is received or the new
message will not be stored in the Queue memory.
The icon lights when a message is stored in the Queue
memory.
1
Press the key programmed as Queue to enter Queue
Mode.
2
Rotate the selector or press the <B and C> keys to select
the desired message.
•
Press and hold the S or
ID/ status ID, the channel name, and the time of the received
message.
key to toggle between the called
3
Press the S or key to return to Normal Operation Mode.
•
To delete the selected message, press the A or # key. To
confirm the deletion, press the S or key.
To delete all messages, press and hold the A or # key for
1 second. To confirm the deletion, press the S or key.
•
25
FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION
FleetSync is an Alphanumeric 2-way Paging Function, and is
a protocol owned by KENWOOD Corporation. FleetSync
enables a variety of paging functions on your transceiver,
some of which depend on dealer programming.
Note: Your transceiver functions include either FleetSync or 5-tone
Signaling {page 22}, but not both.
SELCALL (SELECTIVE CALLING)
A Selcall is a voice call to a particular station or to a group of
stations.
I TRANSMITTING
1
Select your desired zone and channel.
2
Press the key programmed as Selcall or
Selcall + Status to enter Selcall Mode.
3
Rotate the selector or press the <B and C> keys to
select the ID of the station you want to call.
•
•
Alternatively, you can enter a station ID using the DTMF
keypad.
If Manual Input Mode is enabled, you can enter digits by
using the DTMF keypad or by selecting digits with the
selector. To enter Manual Input Mode, first press and
hold the S or
key. When using the selector, rotate it to
select a digit, then press the C> key to accept the digit
and shift the cursor to the right. Repeat this process until
the entire ID is entered.
4
Press the PTT switch and begin your conversation.
•
Alternatively, you can press the Side 2 key to page the
selected station, rather than making a voice call.
26
I RECEIVING
An alert tone will sound, the transceiver will automatically
enter Selcall Mode, and the calling station’s ID will appear
when a Selcall is received.
To respond to the call, press the PTT switch and speak
into the microphone.
I IDENTIFICATION CODES
An ID code is a combination of a 3-digit Fleet number and
a 4-digit ID number. Each transceiver must have its own
Fleet and ID number.
•
•
Enter a Fleet number (100 ~ 349) to make a group call.
Enter an ID number (1000 ~ 4999) to make an individual call
in your fleet.
•
•
•
Enter a Fleet number make a call to all units in the selected
fleet (Interfleet call).
Select “ALL” Fleet and enter an ID number to make a call to
the selected ID in all fleets (Supervisor call).
Select “ALL” Fleet and “ALL” ID to make a call to all units
(Broadcast call).
Note: The ID range may be limited by programming.
STATUS MESSAGE
You can send and receive 2-digit Status messages which may
be decided in your talk group. Messages can contain up to 16
alphanumeric characters. Status messages range from 10 to
99 (80 ~ 99 are reserved for special messages).
A maximum of 15 received messages can be stored in the
Queue memory of your transceiver. These saved messages can
be reviewed after reception. Depending on your dealer settings,
when the Queue memory is full, either the oldest message will be
erased when a new message is received or the new message
will not be stored in the Queue memory. The icon lights when
a message is stored in the Queue memory.
27
I TRANSMITTING
1
Select your desired zone and channel.
2
Press the key programmed as Status to enter Status
Mode or Selcall + Status to enter Selcall Mode.
•
When using the Status key to enter Status Mode, the
station ID is fixed and cannot be selected. Skip to step 5
to continue.
3
In Selcall Mode, rotate the selector or press the <B
and C> keys to select the ID of the station you want to
call.
•
Alternatively, you can enter a station ID using the DTMF
keypad.
•
If Manual Input Mode is enabled, you can enter digits by
using the DTMF keypad or by selecting digits with the
selector. To enter Manual Input Mode, first press and
hold the S or
key. When using the selector, rotate it to
select a digit, then press the C> key to accept the digit
and shift the cursor to the right. Repeat this process until
the entire ID is entered.
4
5
Press the S or key to enter Status Mode.
Rotate the selector or press the <B and C> keys to
select the status ID you want to transmit.
•
•
Alternatively, you can enter the status ID using the DTMF
keypad.
If Manual Input Mode is enabled, you can enter digits by
using the DTMF keypad or by selecting digits with the
selector. To enter Manual Input Mode, first press and
hold the S or
key. When using the selector, rotate it to
select a digit, then press the C> key to accept the digit
and shift the cursor to the right. Repeat this process until
the entire ID is entered.
6
Press the PTT switch or Side 2 key to initiate the
Status call.
•
“
” is displayed when the call has been
successfully transmitted.
28
I RECEIVING
The icon will flash and a calling ID or text message will
appear when a Status call is received.
Press any key to return to Normal Operation Mode.
I REVIEWING MESSAGES IN THE QUEUE MEMORY
1
Press the key programmed as Queue to enter Queue
Mode.
•
The last received message is displayed with the message
number.
2
Rotate the selector or press the <B and C> keys to
select the desired message.
•
Press and hold the S or
message/ call ID, the channel name, and the time of the
received message.
key to toggle between the
3
Press the S or key to return to Normal Operation Mode.
•
To delete the selected message, press the A or # key. To
confirm the deletion, press the S or key.
To delete all messages, press and hold the A or # key for
1 second. To confirm the deletion, press the S or key.
•
SHORT MESSAGES
To send a short message, you must connect the transceiver to
a PC. Ask your dealer for details.
•
•
Short messages can contain a maximum of 48 characters.
Received short messages are displayed the same as Status
messages and are stored in the same Queue memory. A
combined maximum of 15 Status calls and short messages can
be stored in the Queue memory.
LONG MESSAGES
To send and receive long messages, you must connect the
transceiver to a PC. Ask your dealer for details.
•
Long messages can contain a maximum of 4096 characters.
29
DTMF (DUAL TONE MULTI FREQUENCY) CALLS
MANUAL DIALING
I METHOD 1
Press and hold the PTT switch, then enter the desired
digits using the front panel keypad.
•
•
If you release the PTT switch, transmit mode will end even if
the complete number has not been sent.
If your dealer has activated the Keypad Auto PTT function,
you need not press the PTT switch while entering digits. The
DTMF code will be sent automatically when you press a key.
I METHOD 2
Enter the desired digits using the front panel keypad
(maximum of 30 digits). After entering the complete
number, press the PTT switch.
•
The DTMF code is transmitted after pressing the PTT switch.
Note: Switching OFF the transceiver power clears the number.
AUTODIAL
Autodial allows you to store and quickly recall 32 names (up
to 12 characters per name) and DTMF numbers (up to 16
digits per number).
REDIAL
1
To redial the last called number, press the key
programmed as Autodial.
•
The first entry in the Autodial list appears on the display.
2
3
Press the key followed by the 0 key to display the last
called number.
Press the PTT switch to make the call.
Note: Switching OFF the transceiver power clears the redial memory.
30
CONNECT/ DISCONNECT IDS
1
Press the key programmed as Autodial.
•
The first entry in the Autodial list appears on the display.
2
3
Connect ID: Press the key two times.
Disconnect ID: Press the key followed by the # key.
Press the PTT switch to make the call.
DTMF SIGNALING
DTMF Signaling is either enabled or disabled by your dealer.
This function opens the squelch only when the transceiver
receives the DTMF code programmed in your transceiver.
Each transceiver is normally programmed with a unique code.
You will not hear calls from transceivers that are not
programmed with a matching code.
When you receive a signal containing the correct tones,
squelch opens and you will hear the call.
•
•
The LED indicator flashes orange.
To mute the speaker after squelch opens, press the key
programmed as Monitor.
•
•
•
Your dealer can program the squelch to close again after a
specific time period elapses.
If Transpond for DTMF Signaling is programmed, an
acknowledgment signal is returned to the calling station.
If Tone Alert for DTMF Signaling is programmed, an alert tone will
sound when the correct tones are received.
STUN
This function is used when a transceiver is stolen or lost.
When the transceiver receives a call containing a stun code,
either transmit mode will be disabled, or both receive mode
and transmit mode will be disabled. Stun is cancelled when
the transceiver receives a call with a revive code.
31
VOICE OPERATED TRANSMISSION (VOX)
VOX can be activated or deactivated by your dealer. VOX
operation allows you to transmit hands-free. This feature can
only be used if you are using a supported headset.
When operating VOX, you must set a VOX Gain level. This
setting allows the transceiver to recognize sound levels. If the
microphone is too sensitive, it will begin transmitting when
there is noise in the background. If it is not sensitive enough,
it will not pick up your voice when you begin speaking. Be
sure to adjust the VOX Gain level to an appropriate sensitivity
to allow smooth transmission.
To set the VOX Gain level, perform the following steps:
1
Connect the headset to the transceiver.
•
The VOX function does not activate when a headset is not
connected to the accessory terminal of the transceiver.
2
3
Press the key programmed as VOX.
•
The current VOX Gain level appears.
Press the <B and C> keys to increase or decrease the
VOX Gain level.
•
The VOX Gain can be adjusted from levels 1 to 10.
4
While adjusting the gain level, speak into the headset
microphone as you would while under normal operation, to
test the sensitivity level.
•
When the microphone recognizes a sound, the LED lights
orange. This allows you to determine a suitable level where
background noise will not activate VOX operation while
speaking into the microphone will.
•
The transceiver does not transmit your voice during this test
procedure.
5
Press the S or key to save the setting.
32
To activate the VOX function:
1
Connect the headset to the transceiver.
•
The VOX function does not activate when a headset is not
connected to the accessory terminal of the transceiver.
2
Press and hold the key programmed as VOX.
•
The duration for holding the VOX key is programmed by your
dealer.
•
The VOX indicator (
) appears on the display.
3
To turn the VOX function OFF, press and hold the VOX
key again.
Note:
N
If a speaker/ microphone is connected to the transceiver while the
VOX function is switched ON and the VOX Gain Level is configured
to a higher, more sensitive level, louder received signals may cause
the transceiver to start transmission.
N
When you operate the VOX function, you must use an optional
KHS-11BL, KHS-12BL, KHS-14, KHS-15-BH, or KHS-15-OH
accessory.
33
EMERGENCY CALLS
If your transceiver has been programmed with the Emergency
function, you can make emergency calls.
Note: Only the Auxiliary (orange) key and the PF1 (orange) key of
the optional KMC-25 speaker/ microphone can be programmed with
the Emergency function.
1
2
Press and hold the key programmed as Emergency.
•
•
Depending on the delay time programmed into your
transceiver, the length of time you must hold the Emergency
key will vary.
When the transceiver enters Emergency mode, the
transceiver will change to the Emergency channel and begin
transmitting based on how the transceiver is set up by your
dealer. Transmit periods are also set by your dealer.
To exit Emergency mode, press and hold the Emergency
key again.
•
If the Emergency mode completes the preset number of
cycles, Emergency mode will automatically end and the
transceiver will return to the channel that was in use before
Emergency mode was entered.
Note:
N
Your dealer can set a beginning of transmit and end of transmit
tone for the transceiver.
N
Your dealer can set the transceiver to emit tones and received
signals as normal or mute the speaker during Emergency
operation.
34
ADVANCED OPERATIONS
SELECTING A TRANSMIT POWER
Each channel is programmed with either high or low transmit
power by your dealer. You can change the transmit power of
only channels programmed as high.
When you can reliably communicate with other parties without
using high transmit power, select low transmit power by
pressing the key programmed as Low Transmission Power.
Each time you press Low Transmission Power, the transmit
power toggles between high and low.
•
•
The icon appears while using low transmit power.
Using low transmit power conserves battery power and reduces
the risk of interfering with other communications.
Note: Pressing Low Transmission Power while using a channel
programmed with low power causes an error tone to sound.
TALK AROUND
You may occasionally experience an interruption in service
(due to a power failure, etc.). During such an occurrence, you
can continue communication by using the Talk Around feature.
Talk Around allows you to communicate directly with other
transceivers, without the use of a repeater. However, if the
station you want to contact is too far away, or there are
geographical obstacles in the way, you may not be able to
contact the station.
Toggle Talk Around ON and OFF by pressing the key
programmed as Talk Around.
•
The icon appears on the display while Talk Around is active.
•
When using Talk Around, the receive frequency is used for both
transmitting and recieving, and the decode signaling is used for
both encoding and decoding.
35
MONITOR/ SQUELCH OFF
You can use the key programmed as Monitor/ Squelch Off to
listen to weak signals that you cannot hear during normal
operation and to adjust the volume when no signals are
present on your selected channel.
•
The icon appears on the display while Monitor/ Squelch Off is
activated.
Your dealer can program a key with one of 4 functions:
•
Monitor: Momentarily press to deactivate QT, DQT,
DTMF, 5-tone, or FleetSync Signaling. Press the key
again to return to normal operation.
•
Monitor Momentary: Press and hold to deactivate QT,
DQT, DTMF, 5-tone, or FleetSync Signaling. Release the
key to return to normal operation.
•
•
Squelch Off: Momentarily press to hear background
noise. Press the key again to return to normal operation.
Squelch Off Momentary: Press and hold to hear
background noise. Release the key to return to normal
operation.
I SQUELCH LEVEL
To adjust the squelch level:
1
2
Press the key programmed as Squelch Level.
Press the <B key to decrease the squelch level (open)
and the C> key to increase the squelch level (tighten).
•
Alternatively, you can increase or decrease the squelch
level by rotating the selector.
3
Press the S or key to store the new setting and exit
the squelch level adjustment.
36
KEY LOCK
This function is used to help prevent any accidental operation
of the transceiver.
To lock the transceiver keys, press and hold the key
programmed as Key Lock.
•
The duration for holding the Key Lock key is programmed by
your dealer.
•
•
"
" appears on the display.
You can continue to use the following programmable functions (if
available): Emergency, Function, Key Lock, Lamp, Monitor,
Monitor Momentary, Squelch Off, and Squelch Off
Momentary.
To unlock the keys, press and hold the Key Lock key again.
SCRAMBLER
Although the scrambler function does not offer complete
privacy with your calls, it does prevent others from easily
listening in on your calls. When activated, the transceiver
distorts your voice so that anybody listening to your call will
be unable to clearly hear what you are saying.
In order for members of your own group to clearly hear your
call while you are using the scrambler, all other members
must also activate the scrambler functions on their
transceivers. This distorts everybody’s voice while
transmitting and corrects the voice message on your own
transceiver when you receive the call.
To activate the scrambler, press the key programmed as
Scrambler.
•
The icon appears on the display while the scrambler is active.
To deactivate the scrambler, press the Scrambler key again.
Note: There are 2 options for using the scrambler. Your dealer can
activate or deactivate the built-in scrambler function of the
transceiver, or they can add a more secure optional scrambler board
to your transceiver. Ask your dealer for details.
37
CLOCK
If activated by your dealer, your transceiver can track the time
and date with its built-in clock. The time will display
momentarily when the transceiver power is turned ON.
Additionally, you can view the clock any time by pressing the
key programmed as Clock.
Note: Removing the battery pack or leaving the battery pack
uncharged for extended periods will cause the clock time to clear.
I CLOCK SETUP
To set the year, month, day, and time:
1
With the transceiver power OFF, press and hold the
C> key while turning the transceiver power ON.
•
The current year setting appears.
2
Rotate the selector to select the year, then press the
S key to cycle to the month setting.
•
Repeat this step, to cycle through the day, hour, and
minute settings.
3
4
Press the S key again, to return to the year setting.
•
A triple beep will sound, indicating that your selections
have been set into the transceiver memory.
Turn the transceiver power OFF and then back ON to
return to Normal Operation Mode.
TRANSCEIVER BACKLIGHT
To turn the transceiver display and front panel keypad
backlight on, press the key programmed as Lamp.
•
Pressing any key other than the PTT switch, the Power switch/
Volume control, and the Lamp key while the backlight is on will
reset the backlight timer, allowing it to remain lit for an additional
5 seconds.
To turn the transceiver backlight off immediately, press the
Lamp key while the backlight is on.
38
BACKGROUND OPERATIONS
TIME-OUT TIMER (TOT)
The purpose of the Time-out Timer is to prevent any caller
from using a channel for an extended period of time.
If you continuously transmit for a period of time that exceeds
the programmed time set by your dealer (default is 1 minute),
the transceiver will stop transmitting and an alert tone will
sound. To stop the tone, release the PTT switch.
Your dealer can program the TOT time in the range of
15 seconds to 20 minutes.
BUSY CHANNEL LOCKOUT (BCL)
When activated, BCL prevents you from interfering with other
parties who may be using the same channel that you
selected. Pressing the PTT switch while the channel is in use
will cause your transceiver to emit an alert tone and
transmission will be inhibited (you cannot transmit). Release
the PTT switch to stop the tone and return to receive mode.
If activated, you can override this function. To override BCL,
press the PTT switch again immediately after releasing it
(within half a second).
Note: Ask your dealer for an explanation on how BCL functions
when using QT, DQT, DTMF, 5-tone, or FleetSync signaling.
BATTERY SAVER
If activated by your dealer, the Battery Saver function will
decrease the amount of power used when a signal is not
being received and no operations are being performed (no
keys are being pressed, and no switches are being turned).
While the channel is not busy and no operation is performed for
5 seconds, Battery Saver turns ON. When a signal is received
or an operation is performed, Battery Saver turns OFF.
39
BATTERY POWER INDICATOR
The battery power indicator displays the battery power
remaining, as illustrated below:
High
Sufficient
Low
Very low (flashing)
When the battery power is very low, replace or recharge the
battery pack. If activated by your dealer, an alert tone will
sound every 30 seconds and the LED indicator will blink red
when the battery power is low.
SIGNAL STRENGTH INDICATOR
The signal strength indicator displays the strength of received
calls:
Strong signal
Medium signal
Weak signal
Very weak signal
BEGINNING/ END OF TRANSMIT SIGNAL
The Beginning of Transmit and End of Transmit identification
signals are used to access and release some repeaters.
If Beginning of Transmit is set, the ID signal is transmitted
when you press the PTT switch.
If End of Transmit is set, the ID signal is transmitted when you
release the PTT switch.
If both are set, the ID signal is transmitted when you press
and release the PTT switch.
40
VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT
When using the optional VGS-1 voice guide & storage unit,
you gain access to the voice recorder and voice
announcement functions. Ask your dealer for details.
VOICE RECORDER
The voice recorder function allows you to record your
conversations and create voice memos and automated
message responses.
I AUTO RECORDING
If activated, the auto recording function will continuously
record all transmitted and received signals. The recording
storage area retains 30 seconds of recording, so all
transmitted and received signals are simultaneously
recorded and erased, leaving only the last 30 seconds of
recording in memory.
•
The auto recording indicator (
this function is activated.
) appears when
I VOICE MEMOS
To record a voice memo, for later playback:
1
Press the key programmed as Voice Memo.
•
The duration of recording memory will appear on the
display and begin counting down.
2
3
Speak into the transceiver to record your voice memo.
Press the Side 2, S, or key to end the recording at
any time and store it into the transceiver memory.
•
If the memory becomes full, recording will stop
automatically and store the voice memo to memory.
•
“
” appears on the display while the recording is
being stored to memory.
41
I AUTO REPLY MESSAGE
You can set the transceiver to automatically respond to
Individual Calls (while using FleetSync):
1
Press the key programmed as Auto Reply Message to
enter Auto Reply Message mode.
•
The Auto Reply Message indicator (
appears on the display.
)
2
When you receive an Individual Call, Auto Reply will
begin after waiting for 3 seconds, the transceiver will
send an automatic response to the caller, and
“
” appears on the display.
•
If you are available to receive the call, press any key to
disable the auto response.
•
•
If memory is available on your transceiver for recording, "I
am not available. Leave your Message." will be sent to
the caller. The caller can then leave a recorded message
on your transceiver which you can later recall and listen
to. When a message is stored on your transceiver,
"
" appears on the display.
If no memory is available on your transceiver for
recording, "I am not available." will be sent to the caller
and “
” appears on the display.
42
I PLAYBACK
To play back a recorded conversation, memo, or message:
1
Press the key programmed as Playback to enter
Playback mode.
•
If the last action on your transceiver was to auto record
your conversation, " " will appear on the display,
otherwise a recording channel with the time of the
recording will appear. To store the conversation record in
the next available recording channel, press the Side 2
key. To clear the conversation, press the A or # key. To
skip to the stored recording channels, press the S
or key. To skip back 5 seconds, press the <B key. To
skip ahead 5 seconds, press the C> key.
2
3
Rotate the selector to select the channel which you
want to play back.
•
•
•
"
"
"
" represents automated reply messages.
" represents conversation records.
" represents voice memos.
The transceiver will announce the channel, then the
recording will automatically play back.
•
When the entire recording has been played, “
(end of message) is displayed.
”
•
To delete the selected recording, press the A or # key. To
clear all the recorded data, press and hold the A or # key.
A confirmation message will appear on the display. Press
the S or key to delete the recording(s) or the A or # key
to cancel.
VOICE GUIDE
When changing the zone, channel, or operation mode, an
audio voice will announce the new zone, channel, or mode,
after it has been selected. (Voice Annunciation can be
activated or deactivated by your dealer.)
43
|